본문 바로가기

진동기준27

NEMA MG-1 (2014) NEMA Standards Publication MG 1-2006 Motors and Generators 이 규격은 Vendor shop에서 Test 수행 시 적용하는 Vibration limit를 제공하고 있으며, 아래 전동기에 기본적으로 적용한다. 한편, 본 규격은 Site 운전 조건에서는 적용하지 않으며, 현장 운전 조건에 대한 Vibration limit은 ISO 10816-3을 참조하도록 한다. - DC, AC 전동기 - Frame Size가 42 이상인 경우, - 75MW까지 출력을 가지고, 운전 속도가 3,600rpm 이하의 전동기 1. Shaft Height에 따른 Bearing Housing 진동 기준치 (Peak) ○ 상기 기준치는 No load, Uncoupled 조건 및 Spring.. 2020. 5. 26.
IEC 60034-14 (Ed. 3.1, 2007) Rotating electrical machines - Part 14 : Mechanical vibration of certain machines with shaft heights 56mm and higher - Measurement, evaluation and limits of vibration severity 이 규격은 Vendor shop에서 Test 수행 시 적용하는 Vibration limit을 제공하고 있으며, 아래 전동기에 기본적으로 적용한다. 한편, 본 규격은 Site 운전 조건에서는 적용하지 않으며, 현장 운전 조건에 대한 Vibration limit은 ISO 10816과 ISO 7919를 참조하도록 한다. - DC, AC 전동기 - Shaft height가 56mm 이상인 경우 - 50.. 2020. 5. 25.
ISO 7919-5 (2nd, 2005) Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 5 : Machine sets in hydraulic power generating and pumping plants 이 규격은 현장의 정상 운전 조건 하에서 수력 발전과 펌프 설비 내의 기계나 기계 세트의 베어링 주변 Shaft에서 평가된 진동 기준에 적용되는 지침이다. 진동 기준치는 Shaft 측정 면에서 최대 진동 변위 값과 변위 P-P값에 따라 각각 적용한다. ○ Major range A-B : Acceptable for unrestricted long-term operation ○ Major range C-D : Machin.. 2020. 5. 23.
ISO 7919-4 (2nd Edition, 2009) Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 4 : Gas turbine sets with fluid-film bearings 이 규격은 출력 3MW를 초과하고, 축 회전속도 3,000rpm에서 30,000rpm 범위에 있는 유막 베어링을 채택하는 Gas turbine의 현장에서 측정된 진동 평가에 사용된다. ○ Zone A : Newly commissioned machine ○ Zone B : This zone is considered as acceptable level for unrestricted long-term operation ○ Zone C : Normally co.. 2020. 5. 21.
ISO 7919-3 (2nd Edition, 2009) Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3 : Coupled industrial machines 적용 대상은 유막 베어링으로 지지되는 운전속도 1,000 ~ 30,000rpm의 산업용 기계로서, 50MW이하의 Steam Turbine, 터보압축기, 터보 펌프, 터보 fan 등의 현장에서 측정된 진동 평가에 적용될 수 있다. 통상 산업용 기계에서는 베어링에 대한 축의 상대진동을 측정하므로, 별도 다른 언급이 없을 경우 항상 상대 진동 변위를 적용하도록 하며, 동일 기계의 베어링 하우징 진동 평가는 ISO 10816-3, ISO 10816-7을 적용한다. ○ Zone A : .. 2020. 5. 13.
ISO 10816-7 (1st Edition, 2009) Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 7 : Rotodynamic pumps for industrial applications, including measurements on rotating shafts ISO 10816-7은 아래 해당하는 기기의 Site에서 측정된 진동값의 평가에 적용하며, Bearing Housing 위치에서 측정된 진동을 RMS 단위로 평가하는데 이용한다. ● 1kW 이상의 출력을 가지는 펌프 ● 모터 Shaft와 Rigid Coupled Type으로 연결되어 있는 펌프 & 모터 ● 모터 Shaft와 Flexible Coupled Type으로.. 2020. 5. 2.
ISO 10816-6 (1st Edition, 1995) Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 6 : Reciprocating machines with power ratings above 100kW ISO 10816-6은 아래 해당하는 기계의 Site에서 측정된 진동값의 평가에 적용하며, 규격에서 제시하는 위치에서 측정된 진동을 RMS 단위로 평가하는데 이용한다. ● It generally applies to reciprocating piston machines mounted either rigidly or resiliently with power ratings of above 100 kW. Typical examples.. 2020. 5. 1.